Tutorial - Altered Double Display Card

I had an email from a lovely lady named Ann, who wanted to create a card based on a picture she found on the internet. After much fiddling, researching, measuring and many failed attempts, I think I finally managed to figure out the design, which to me, looks like an altered version of a double display card.

As you can see, it stands open beautifully making it perfect for those extra special occasions where you want your cards to be displayed for all to see. And believe it or not, it will still fold into a nice 6" x 4" card that fits perfectly into a standard envelope.

TEMPLATE

1. Begin with a horizontal piece of card stock measuring 12" x 6". For this particular card, I find it much easier to do the scoring before the cutting so I'm going to start there.

2. Following the template above, lay your card horizontally on your score board and start scoring 1" from the left hand side but just 1" down. Score again at the bottom, coming just 1" up. 

3. Now score at 2" from the left hand side, all the way from the top to the bottom. Score again at 4", all the way from the top to the bottom.

4. Start scoring at 5" from the left hand side, starting at the top and coming down just 1". Score again from the bottom, coming just 1" up.

5. Now turn your card around 180 degrees so that the left hand side is on the right. Repeat steps 2, 3 and 4 so that you have the same score lines on both ends of the card stock. Refer to the template to make sure all your score lines are in the correct place.

6. Time to cut. Using a trimmer or craft knife, make a cut between the bottom of the first score line right through to the bottom of the fourth score line at 5". Your cut should be horizontal and measure 1" from the top edge. Refer to the template for correct placement.

7. Make the same cut at the bottom of the card, starting at the top of the first score line and ending at the top of the fourth score line.

8. Turn your card 180 degrees and repeat steps 6 and 7 so that you have the same cuts on both ends of your card.

9. Time to fold along all the score lines. Use the photograph below to determine the placement of valley folds and mountain folds. It doesn't matter if you fold the wrong way, just push the fold back in the other direction. Press all the creases firmly with a bone folder.

10. Cut two strips of matching card stock measuring 2" x 6". These will be adhered to either end of your card to make solid panels.

11. Decorate the two strips of card stock as desired. I used some white card and pretty patterned paper.

12. Use glue or double sided tape to adhere the strips to either end of the card, taking care to keep the adhesive only on the panel indicated below. If the adhesive is placed on any of the other sections of your card it will not open properly.

13. That's it, you've completed the base! Now all that's left is to decorate the centre keeping in mind that the card is designed to stand open and show off whatever is inside.

Stamps:

Tutorial - Double Shutter Card

These fabulous cards fold out to create a wonderful display piece that you can fill with gorgeous stamps, beautiful patterned papers or even a gallery of different sized photos.  As you can see from the picture below, they are very long and require two pieces of cardstock to create but they still fold up to a standard card size for postage.

Use this template for measuring, scoring and cutting your cardstock.  Pay close attention to where the cuts are situated and where the score lines are marked.  In general, the cut lines are horizontal and the score lines are vertical.

1.  Start with a 12" x 12" sheet of cardstock.

2.  Cut the cardstock in half so you end up with two pieces measuring 12" x 6".

3.  Using the template above, score and cut your two pieces of cardstock.

4.  Mountain and valley fold both pieces of cardstock as shown in the photos below (refer to the template for fold lines).  It's a little tricky to get your fingers around each section as they are very close together.  Make sure you press firmly on each fold for a nice crisp line. 

5.  Adhere the two 4" sections together with glue or double sided tape.  It doesn't matter which side is on top.

View from above.

6.  To decorate, cut 18 patterned paper squares measuring 13/4" x 13/4".  I used two co-ordinating pieces but you could use a single design or even different papers for each square.  Adhere to each of the small panels.  Cut two strips of patterned paper measuring 53/4" x 13/4" for the long sides and adhere.  These will be visible on the front of your card when you fold it up.

7.  Add stamps, embellishments, ribbons or whatever else you would like to complete the inside of your card.

8.  Due to the bulk of the card, it's a good idea to create a belly band to hold it all together when its folded.  I simply used a strip of cardstock, a strip of patterned paper and some embellishments to finish it off.  My band forms the main decoration for the front of my card.

  

All photos and written instructions are copyright Beccy Muir 2014.

ADDITIONAL INSTRUCTIONS (added: 08.08.17)
Here is a step-by-step photo tutorial for folding the sides of the card correctly. It can be a little tricky to get all the little squares to fold up in the right places!